|
Ot
<br /> VCOM-AX2OB /PT UV lB RG Panel Operation
<br /> 1.000-340-0043
<br /> Overview Inputs& Output Definitions
<br /> The VCOM-AXB/PT UV IB RG telemetry- The following inputs and outputs are used with your control panel:
<br /> enabled panel is used for remote monitoring and
<br /> control of the dual pumping operations of time- Expansion Modem serial Port RS232Nest Button
<br /> elsut Outputs(4)�gz Activity
<br /> dosed Recirculating and Discharge pumps with a = 1 , e, „,is ,
<br /> drip system. si ,; 1 4 t a ~- - Input Fuse
<br /> 5•Split Rite j ,LM, d 1 >im r F F,i 14 n u s., t 1 power
<br /> Basic control logic manages the day-to-day Yeh F17 v z Y 1..�, i _ t t p'1 w is: , ;L '� 1t t Connector
<br /> g g Y y 6-Drip Rush nG t 1 tc il i g , I. i.
<br /> functionality of the control panel. The VCOM- vow rM9; �.1-1, .__ - , ' t 41 va ' s,a
<br /> AXE/PT UV IB RG system recirculates the 7-Zone ea pi I r,o , �—s f �'1y IV E ,' 1 4-Audible Nate
<br /> 0 rs 4 F44, 1,:t-r MOW t?4'e �°n� FP? .L.-� 2 -1-- 3-Alarm Light
<br /> blend four to five times;until the recirculatingI v e ' g , > e a
<br /> �p n^i 1 i`�xl�lpuis(4► � r;t �� ,.` aa� t �:
<br /> splitter valve(RSV)seats,then small amounts of 4a I a i`" e, «rs r h ,} -"` ,fir c 2-Olschargo Pump
<br /> i A a ,tx �y 4;ti r p`' , i�3 16 6 I O` 4 , tea I Recite.Pump
<br /> treated wastewater are pumped into the • � ;in* 6,0:011 F i—. ,,,,, ff J. y�
<br /> discharge tank. As the discharge tank fills, Ou d F,wER/anioo-► } °o, °n.ttuts(e) ii1 it, er a ,t,,A,4
<br /> g g � �rJ��- rT'3 I� rf I °c o o a sip t'TY'lii �L Output Fuse
<br /> effluent is removed through a timed dosing drip -,- s ocao J000 ` ` ' 'V'°'a` '`
<br /> system. During peak flow conditions,each tank Expansion Phone Jack Recite.Bottom Float-1 Power LED
<br /> has more aggressive timer settings to manage POW Connector Rotdre.Mkklla Froat-2
<br /> the increased demand. The drip system is Recite.Top Hoat-3
<br /> Discharge Middle Floa1•4
<br /> periodically flushed to prevent clogging. Discharge rap Fbat-5
<br /> Recite.Aux.Conlnct-R
<br /> Fault conditions are automatically reported to OtschargeAtue Contact-7
<br /> Push To Silence Alarm•0
<br /> the VeriComm Monitoring System and not
<br /> locally at the panel,making the system virtually
<br /> invisible to the homeowner. However,if fault Note:
<br /> conditions are not responded to,or the system I. Digital inputs are the yellow LEDs horizontally aligned along the bottom of the controller,
<br /> cannot communicate with the VeriComm 2. Digital outputs are the red LEDs vertically aligned on the right side of the controller,and
<br /> Monitoring System,then local alarms may be 3. Inputs and outputs are activated by various events(e.g.,Floats are activated when the float is in the up
<br /> activated. position;"Hold-To-Silence"is activated when the push button,located on the front of the panel is pressed).
<br /> To silence local alarms,press the"Hold-To- Analog Inputs:
<br /> Silence"button until the audible alarm stops. 1. Analog Input#1—Discharge Bottom Float(Green indicator light on the float relay).
<br /> 2. Analog Input#2—UV Sensor(LED display on the UV current sensor).
<br /> The procedures outlined in the remainder of 3. Analog Input#3—Rain Sensor(Green indicator light on the rain sensor relay).
<br /> this document are to verify proper
<br /> installation;they should be conducted in the
<br /> sequence outlined while in"Test Mode".
<br /> EIN•CP-uP-2109
<br /> Run 1.1®mul2/IO
<br /> Pagel a15
<br />
|