11985693 - Laserfiche WebLink

Home Browse Search

Septic Permit 555-23-004764-PRMT Page 3 of 4 ClateGetiltel ISStied4V8�/2?23 � A�Z ak y WorkDescripttan i i� P 3 pu s ,��-� � y •This permit is for the installation of an Alternative Treatment Technology(ATT)system and is to be installed by a person certified by the system manufacturer in accordance with OAR 340-071-0600 and 0650.See Alternative Treatment Technology rules at OAR 340-071-0345. •ATT treatment standard 2 required. •The septic tank must be approved for use with the AU system to be installed. •In addition to the As-Built and Materials List,a Start-Up checklist from the AU maintenance provider is required to Final this permit. •The owner of an ATT system must maintain a contract with a maintenance provider certified by the manufacturer to inspect,adjust and maintain the onsite system.The maintenance provider must submit an annual report and annual evaluation fee. •Dry soil installation only(June 1—October 1 unless otherwise authorized by the agent). •The system must be installed by the property owner or a licensed sewage disposal business(installer). •Vehicular traffic and livestock must be restricted from the system area. •All roof drains must be directed away from the system •All tanks must be tested for watertightness and have a water-tight riser to the ground surface.Twenty-inch minimum diameter if less than 36-in deep.Thirty-inch minimum diameter if greater than 36-in deep.Maintain access to septic tank for pumping and service. •Meet all required setbacks •The system must be installed in the area approved during the site evaluation and in accordance with the construction plan approved by the agent,including any changes made by the agent. •All work is to conform to OAR 340,Division 71 and 73.Make no changes in system location or specifications without approval by the agent. •For product approval information and manufacturer installation requirements see DEQ website at: http://www.oregon.gov/deq/Residential/Pages/Onsite.aspx •The pump and alarm must be wired on separate circuits in the control panel.Pump wiring must comply with applicable building,electrical,or other codes.An electrical permit and inspection from the Department of Consumer and Business Services,Building Codes Division,or the municipality with jurisdiction,is required for pump wiring installation. •Install the pump and system components in accordance with the approved pump curve and specifications. •Install the pump and system components in accordance with the approved pump curve and specifications. •An anti-buoyancy device is required for the septic tank(s)and must be installed as per the manufacturer installation guidelines. •A minimum 18-gauge,green jacketed tracer wire or green color-coded metallic tape must be placed on top of the effluent sewer or pressure transport pipe from tank to drainfield. ▪Effluent filter required at pump vault •Equal distribution,all trench bottoms must be at the same elevation.Use Distribution box(es). •ATT treatment standard 2 required. •The septic tank must be approved for use with the ATT system to be installed. •In addition to the As-Built and Materials List,a Start-Up checklist from the An maintenance provider is required to Final this permit. •The owner of an ATT system must maintain a contract with a maintenance provider certified by the manufacturer to inspect,adjust and maintain the onsite system.The maintenance provider must submit an annual report and annual evaluation fee. •Dry soil installation only(June 1 —October 1 unless otherwise authorized by the agent). •The system must be installed by the property owner or a licensed sewage disposal business(installer). •Vehicular traffic and livestock must be restricted from the system area. •All roof drains must be directed away from the system •All tanks must be tested for watertightness and have a water-tight riser to the ground surface.Twenty-inch minimum diameter if less than 36-in deep.Thirty-inch minimum diameter if greater than 36-in deep.Maintain access to septic tank for pumping and service. •Meet all required setbacks •The system must be installed in the area approved during the site evaluation and in accordance with the construction plan approved by the agent,including any changes made by the agent. •All work is to conform to OAR 340,Division 71 and 73.Make no changes in system location or specifications without approval by the agent. •For product approval information and manufacturer installation requirements see DEQ website at: 12/19/23:9:05:59AM ONS_OnsiteCSCJDr