8620333 - Laserfiche WebLink

Home Browse Search

VCOM-AX2OB /PT UV IB RG Panel Operation Orem°Stems. Incorporated 1-800-348-9843 Overview Inputs & Output Definitions The VCOM-AXB/PT UV IB RG telemetry- The following inputs and outputs are used with your control panel: enabled panel is used for remote monitoring and control of the dual pumping operations of time- Expansion Modem Serial Port RS232Test Button Digital Outputs(4) Activity dosed Recirculating and Discharge pumps with a pin-U.100 .� , L drip system. Q, �, 511 i - - Input Fuse 5-Spin Fitter ' p Valve __—�" F_ , S1+ (61 pi i1�rt , Power Basic control logic manages the day-to-day 6-Drip Flush 'GI' - - "5-� '''Y -1u�!r I , e 2- connector Y functionality of the control panel. The VCOM- Valve IGS- �?, � : f,' ala "I, • ?, AXB/PT UV IB RG system recirculates the 7-Zone Valve °�. � s�`'� -.$.1/4.:• , ' IN � i ,,r Signal alve t-; , . Ir ,. f'-��— 4-Audible Alarm blend four to five times;until the recirculating • Digital , y 3-Alarm Light • 44 Outputs(4) r. valve(RSV) E— r = splitter seats then small amounts of �� ( 4' -'' `�` `` �� ,.;, 2-Discharge Pump treated wastewater are pumped into the ``"' r Digital • rt �E .-`3..F.51,... Ir2T3"FF'3B.{/al ' ice-- r 1-Recirc.Pump Expansion InPuts 8 discharge tank. As the discharge tank fills, output Fuse"'►- , °c c p O �',I, ,,__L;,-). -1-177----".r � 0 0 0 o a air 11-1-1,111 • 0o ,,- -Output Fuse effluent is removed through a timed dosing drip - c�©0015cot > > , ; w)a,„a system. During peak flow conditions,each tank Expansion Phone Jack r Recirc.Bottom Float-1 �Poaver LED has more aggressive timer settings to manage Power Connector Recirc.Middle Float-2 the increased demand. The drip system is Recirc.Top Float-3 periodically flushed to prevent clogging. Discharge Middle Float-4 Discharge Top Float- Recirc.Aux.Contact-6 Fault conditions are automatically reported to Discharge Aux.Contact-7 the VeriComm Monitoring System and not Push To Silence Alarm-6 locally at the panel,making the system virtually invisible to the homeowner. However,if fault Note: conditions are not responded to,or the system 1. Digital inputs are the yellow LEDs horizontally aligned along the bottom of the controller, cannot communicate with the VeriComm 2. Digital outputs are the red LEDs vertically aligned on the right side of the controller,and Monitoring System,then local alarms may be 3. Inputs and outputs are activated by various events(e.g.,Floats are activated when the float is in the up activated. position;"Hold-To-Silence”is activated when the push button,located on the front of the panel is pressed). - To silence local alarms,press the"Hold-To- Analog Inputs: 1. Analog Input#1—Discharge Bottom Float(Green indicator light on the float relay). Silence"button until the audible alarm stops. 2. Analog Input#2—UV Sensor(LED display on the UV current sensor). The procedures outlined in the remainder of 3. Analog Input#3—Rain Sensor(Green indicator light on the rain sensor relay). this document are to verify proper installation;they should be conducted in the sequence outlined while in"Test Mode". EI N-CP-O P-2109 Rev 1.1 ©09/12/10 Pa0e1 of 5