Permit - 1271650 - Laserfiche WebLink

Home Browse Search

PorcheS, balconies or raised floor surfaces located more than 30 in, above the floor or grade shall have guardrails not less than 36 in. in Required guardrails shall have intermediate rails or ornamen- tal closures which will not allow passage of an object 6 in , or more in diameter. R- 214.2 installed ogtside of each separate sleeping area in the immed~ ate vicinity of the bedroo~s and on each additional story of the dwelling including basementS, In dwelling units with split levels¢ e smoke detector need be installed only on the upper level, provided the lower level is less than one full story below the upper level, except that if there is a door between levels then a detector is required on each level. All detectors shall be connected to a sounding device or other detectors to provide, when actuated, an alarm which will be audible in all sleeping areas. R-215.1 28. 22. In new construction, required smoke detectors shall receive their primary power from the building wiring. Smoke detec- tors may be battery operated when installed in existing buildings. R-215.2 23. Pirestopping shall be provided in the following locations: in concealed spaces of stud walls at the ceiling, floors,soffits, drop ceilings, between stair stringers and at openings around vents, pipes, ducts, chimneys and fireplaces at ceil,ing and floor spaces. R- 402.7 24~ Foundation cripple walls shall be framed of studs with a min. length of 14 in. or shall be framed of solid blocking. R- 402.9 .;5. The area within the foundation walls shall have all vegeta- tion, top soil and foreign material removed. R-603,2 Rafters shall be nailed to ceiling joists to for~ a con- tinuous tie between.exterior ~all$ where joist are parallel to the rafters. Where not parallel, rafters shall be tied with a rafter tie, located at or near the plate as practical. Rafter ties shall be spaced not more than 4 feet on center. Ridge board ehall be at least 1 inch nominal thickness and not less in depth than the cut er]d of the rafter. At all valleys and hips there shall be a valley or hip rafter not less than 2 in. nominal tt%icknesS and not less in depth than the cut end of the rafter, R-702.2 When the roof pi%ch is less than 3 in 12~ members support- lng rafters and ceiling joist, such as ridge beams, t~ips and valleys, shall be des~g.n<~d a~ beams. R-702.3 Wood trusses shall bo designed in accordance with approved engiaeering practice. TruSses shall be braced accordi~g to their appropriate eag~neered design. Truss members shall no~ be cut or altered unless so designed. R-702.9 All plywood, when designed to be exposed in outdoor applica- tions shall be of an exterior type, except that plywood roof sheathing exposed to the underside may be of interior type with exterior glue. R- 703.1 Provide screened attic vents with a net free area of 1/150 of the at~ic area (or 1/300 if half is aloeg eaves and %he other half in uhe upper portion). R-707 A readily accessible a~tic access framed opening not less than 22 in, by 30 in. shall be provided. R-708 33, Fireplace and chimney con- struction shall conform to chapter 9. 34, INSULATION i{EQUi REMENTS : Buildings with high-efficiency heatiag equipment shall be insulated as follow: ceiling R-30 (roof/ceiling assemblies in which has a slope of 3 in 12 or greater, may be R-19), walls R-il, underfloors R-19, other heating systems, ceiling R-38 (vaulted ceiling walls R-19 and under floor 19. Elements of appliances which create a glow, spark or flame shall be located a min. of 18 in. above garage floor. 1114 Appliances subject to mechani- cal damage shall be guarded by a protective barrier. M-1114