12014285 - Laserfiche WebLink

Home Browse Search

• HD Fowler Company Submittal Sec.5:Ln 3:Sec.5:Ln 4:Sec.5:Ln 5:Sec.5:Ln 6:Sec.5:Ln 7:Sec.5:Ln 8:Sec.5:Ln 9:Sec.5:Ln 10 Vendor..67230 CHARLOTTE PIPE AND FOUNDRY COMPANY' SUBMITTAL FOR CHARLOTTE PIPE® ABS CELLULAR (FOAM CORE) PIPE AND ABS DWV FITTING SYSTEM Scope: This specification covers ABS cellular core(foam core)pipe and ABS DWV fittings used in sanitary drain,waste and vent(DWV),sewer,and storm drainage applications.This system is intended for use in non-pressure applications where the operating temperature will not exceed 140°F. sim+Specification: Pipe shall be manufactured from virgin rigid ABS(acrylonitrile-butadiene-styrene)compounds with a cell class of 42222 as identified in ASTM D 3965. Fittings shall be manufactured from virgin rigid ABS compounds with a cell class of 32222 as identified in ASTM D 3965. mom4ABS cellular core pipe shall be Iron Pipe Size(IPS)conforming to ASTM F 628. Injection molded ABS DWV fittings shall conform to ASTM D 2661.All systems shall utilize a separate waste and vent system.All pipe and fittings shall be manufactured in the United States. Pipe and fittings shall conform to NSF International Standard 14. Installation: Installation shall comply with the latest installation instructions published by Charlotte Pipe and Foundry and shall conform to all applicable plumbing,fire,and building code requirements. Buried pipe shall be installed in accordance with ASTM D 2321 and ASTM F 1668.Solvent cement joints shall be made with a solvent cement conforming to ASTM D 2235.The system shall be protected from chemical agents,fire-stopping materials,thread sealant, plasticized-vinyl products or other aggressive chemical agents not compatible with ABS compounds.The system shall be hydrostatically tested after installation.WARNING! Never test with or transport/store compressed air or gas in ABS pipe or fittings. Doing so can result in explosive failures and cause severe injury or death. Referenced Standards: ASTM D 3965: Rigid ABS Compounds ASTM F 628: Co-extruded ABS Pipe with Cellular Core , , ASTM D 2661: ABS Drain,Waste and Vent Fittings ASTM D 2235: Solvent Cements for ABS Pipe and Fittings ABS Foam Core Pipe ASTM D 2321: Underground Installation of Thermoplastic (071 Pipe(non-pressure applications) ABS Schedule 40 DWV Pipe ASTM F 1668: Procedures for Buried Plastic Pipe (For Non-Pressure Applications) NSF Standard 14: Plastic Piping Components and ABS SCHEDULE 40 FOAM CORE(BLACK) PLAIN END ASTM FS28 Related Materials MIN. WT.PER PART NO. NON.SIZE UPC 0 QTY.PER AVE.00 WALL 100 FT. 411942• SEIO RN.) UNJ (IBS.) ABS 3112 11/2"x 10' 03132 2590' 1.900 0.145 27.1 �V:Tee ABS 3112 1'/2"x20' 03133 5180' 1.900 0.145 27.1 �� ABS 3200 2"x 10' 03134 1670' 2.375 0.154 37.7 Coupling Quarter Bend Eighth Bend Doub ABS 3200 2"x 20' 03135 3340' 2.375 0.154 37.7 Sanitar ABS 3300 3"x 10' 03136 750' 3.500 0.216 74.5 11 ABS 3300 3"x 20' 03137 1500' 3.500 0.216 74.5 ABS 3400 4"x 10' 03138 480' 4.500 0.237 107.1 Cleanout Tee Combination Wye P-Trap Closet Flange ABS 3400 4"x 20' 03139 960' 4.500 0.237 107.1 I w/Plug & Eighth Bend ABS 3600 6"x 20' 03141 400' 6.625 0.280 187.8 Not all fitting patterns shown Charlotte Pipe and Foundry Company•P.O.Box 35430 Charlotte.NC 28235•(800)438-8091 •www.charlottepipe.com Charlotte Pipe and Charlotte Pipe and Foundry Company are registered trademarks of Charlotte Pipe and Foundry Company. FO-SUB-ABS(4-10-17)